Hit Improved Version 2x4 Adjuster Set of 6 with Sheets
2x4 Adjuster Set of 6 with Screws Included
Add scratch-resistant sheets for an additional 100 yen. Please comment.
We have up to 7 sets available. Please comment for other quantities.
This is a DIY part for fixing 2x4 lumber vertically to create posts.
If you just want to erect posts, no complicated procedures or special tools are required.
It can be securely fixed using the force of a jack, making it easy to install.
Imitation and plagiarism are prohibited.
Adjusters with only the upper part have existed for a while, but I thought about how to make it work for those who don't have a drill or an 8mm drill, and came up with the idea for the lower part. I came up with the drill-free type.
DIY Storage Parts
Washers have been added between the upper hex and the lumber. This addition provides stability and acts as a lock nut.
Therefore, when assembling the upper part, please insert the washer onto the bolt before inserting it into the hole.
Assembly
Since we ship disassembled, please insert the washer into the bolt as shown in photo 3, lightly tighten it (do not overtighten), then insert the lumber, followed by a washer, nut, nut, and washer in that order, and tighten the upper part with the nut.
Installation Method
① Cut the 2x4 lumber to be used as a post to a length of approximately 80mm less than the installation height.
② Screw the lower part of the adjuster to the top of the 2x4 cut in ①. (Photo 4)
③ Insert the threaded side of the upper adjuster into the hole drilled in the post in ②.
④ Once aligned with the installation location, stand it vertically (use a level), and tighten by turning the lower nut clockwise with a wrench to create tension.
〇 Please sandwich the scratch-resistant sheets between the floor and ceiling, under the post and on top of the adjuster. Attaching them with double-sided tape is easy.
Required Tools
〇 13mm wrench or monkey wrench or similar tool to turn the nut
〇 Electric drill or impact driver or Phillips screwdriver
〇 Saw (You can also have it cut at a home improvement store)
〇 Level (Apps are also available.)
Drill not required
Due to being handmade, there may be slight variations.
Painted versions are also possible, so please contact us.
Any quantity is possible. Please contact us.
Tension Pet Gate
Tension Baby Gate
#Adjuster
#Cat Tower
#Cat Walk
#Wall Mounted TV
#Tension Wall Storage
#Partition
#Fall Prevention
#Escape Prevention Fence
Add scratch-resistant sheets for an additional 100 yen. Please comment.
We have up to 7 sets available. Please comment for other quantities.
This is a DIY part for fixing 2x4 lumber vertically to create posts.
If you just want to erect posts, no complicated procedures or special tools are required.
It can be securely fixed using the force of a jack, making it easy to install.
Imitation and plagiarism are prohibited.
Adjusters with only the upper part have existed for a while, but I thought about how to make it work for those who don't have a drill or an 8mm drill, and came up with the idea for the lower part. I came up with the drill-free type.
DIY Storage Parts
Washers have been added between the upper hex and the lumber. This addition provides stability and acts as a lock nut.
Therefore, when assembling the upper part, please insert the washer onto the bolt before inserting it into the hole.
Assembly
Since we ship disassembled, please insert the washer into the bolt as shown in photo 3, lightly tighten it (do not overtighten), then insert the lumber, followed by a washer, nut, nut, and washer in that order, and tighten the upper part with the nut.
Installation Method
① Cut the 2x4 lumber to be used as a post to a length of approximately 80mm less than the installation height.
② Screw the lower part of the adjuster to the top of the 2x4 cut in ①. (Photo 4)
③ Insert the threaded side of the upper adjuster into the hole drilled in the post in ②.
④ Once aligned with the installation location, stand it vertically (use a level), and tighten by turning the lower nut clockwise with a wrench to create tension.
〇 Please sandwich the scratch-resistant sheets between the floor and ceiling, under the post and on top of the adjuster. Attaching them with double-sided tape is easy.
Required Tools
〇 13mm wrench or monkey wrench or similar tool to turn the nut
〇 Electric drill or impact driver or Phillips screwdriver
〇 Saw (You can also have it cut at a home improvement store)
〇 Level (Apps are also available.)
Drill not required
Due to being handmade, there may be slight variations.
Painted versions are also possible, so please contact us.
Any quantity is possible. Please contact us.
Tension Pet Gate
Tension Baby Gate
#Adjuster
#Cat Tower
#Cat Walk
#Wall Mounted TV
#Tension Wall Storage
#Partition
#Fall Prevention
#Escape Prevention Fence
Category
Cat Towers
Condition
New/unused
Shipping
Included in price (by seller)
From
Shiga
Customers Also Viewed
Was this page helpful?
marty.unleash.wiring disabled
